"注：部分詳情描述與標題不符，價格根據當時銅價核算詳情了解請我司銷售。

MHYV礦用阻燃網線 MHYV礦用網線 4*2*0.5,MHYV礦用網線 4*2*0.8 568A：

電纜與其它管道平行或交叉安裝時均要保持0.5m的距離。

鎧裝阻燃屏蔽控制電纜;ZR-KVVP22,ZR-KVVRP22,ZR-KVVP2-22,ZR-KVVRP2-22 2*0.5,3*0.75,4*4,------37*1.5mm 。

鎧裝控制電纜；KVV22,KVV32,KVVR22 2*0.5,3*0.75,4*4,------37*1.5mm。

PTYA23 21芯鐵路電纜銅導體直徑：1.0毫米直流電阻：≤23.5Ω/km電纜參考外徑：29mm纜芯結構：4×4＋5對絞組工作電容：≤70nF星形四線組工作電容：≤50 nF絕緣電阻：≥3000MΩ/km。

MKVVR 4X1礦用軟芯控制電纜生產


變頻電纜規格范圍;1、芯數：3芯 標稱截面（1.5~240㎜?）。2、芯數：6芯（3+3）標稱截面（主線芯截面：2.5-240㎜?，副線芯截面:0.5-35㎜?）。 例：銅芯0.6/1KV交聯聚絕緣銅絲編織屏蔽，聚氯護套阻燃變頻器用主回路電纜，3×185＋3×35mm2 表示為：BPYJVP-0.6/1KV 3×185＋3×35注：有關電纜的詳細技術參數球我公司垂詢。

成纜工序變頻電纜要求結構對稱，成纜時必須保證絕緣線芯張力均勻，使成纜后的線芯長度盡量保持*，否則會引起結構變化，電容和電感的不均勻性，影響電纜的電氣性能。而且好在具有退扭的成纜設備上完成。
MKVVR 4X1礦用軟芯控制電纜生產


he real facts of the case, and, if necessary, to offer Alen?on a refuge in England. But the Prince’s power, such as it was, had fled, and with it his spirit and his health. Biron kept command of the French garrns in the conquered towns, whilst Alen?on wandered from Vilvorde to Dendremond and thence to Dunkirk, dwed by his brother, and cursed even by his mother for his perversity.

PTYA23 8芯鐵路電纜 銅導體直徑：1.0毫米直流電阻：≤23.5Ω/km電纜參考外徑：25mm纜芯結構：4×2對絞組工作電容：≤70nF星形四線組工作電容：≤50 nF絕緣電阻：≥3000MΩ/km。

(4-37)*(1.5-2.5) 鋪設在大磁場室內、電纜內、管道等固定 。

HYA53、HYA23、HYAT53、HYAT23型適用于直埋，GHYAT、GHYAT53高速公路用通信電纜是為高速公路緊急而設計。
MKVVR 4X1礦用軟芯控制電纜生產


所謂的差分是指一根線以正電平傳輸，另外一根線

When the Master of the Household and Denny suddenly arrived at Hatfield to interrogate the household as to their communications with Seymour Parry quite lost his head, “went to his own chamber and said to his wife, 'I would I had never been born, for I am undone,’ and wrung his hands, cast away his chain from his neck and
MKVVR 4X1礦用軟芯控制電纜生產


礦橡套電纜分為重型橡套軟電纜（YC電纜，YCW電纜），中型橡套軟電纜（YZ電纜，YZW電纜），輕型橡套軟電纜（YQ電纜，YQW電纜），防水橡套軟電纜（JHS電纜，JHSB電纜），電焊機電纜（YH電纜，YHF電纜，YHD電纜）　　 

電焊機電纜產品說明 

本產品適用于對地電壓交流不超過200V和脈動直流峰值400V電焊機用二次側接線及連接電焊鉗.是適用于電焊機二次側接線及連接電焊鉗的電纜,額定電壓交流不超過200V和脈動直流峰值400V。

"